Konfiguracja UrządzeniaDevice Setup
Podłącz i skonfiguruj zasilacz do pracy z K0R@Dus Connect and configure your power supply for use with K0R@Dus
devicesObsługiwane urządzeniaSupported Devices
- KORAD KA3005P / KA3005PS
- KORAD KA3010P / KA3010PS
- KORAD KWR102
- RIDEN RD6006 / RD6006P / RD6006W
- RIDEN RD6010
- RIDEN RD6012 / RD6012P
- RIDEN RD6018
- RIDEN RD6024
- RIDEN RD6030
Zasilacze KORAD porozumiewają się prostym protokołem tekstowym po porcie szeregowym, a zasilacze RIDEN — protokołem Modbus RTU. K0R@Dus obsługuje oba i dobiera właściwy sam, po rozpoznaniu podłączonego modelu.KORAD power supplies communicate using a simple text protocol over the serial port, while RIDEN units use Modbus RTU. K0R@Dus supports both and selects the right one itself, once it recognises the connected model.
cableOpcje połączeniaConnection Options
USB (zalecane)USB (recommended)
Połączenie USB jest najprostsze i najbardziej niezawodne. Zasilacz pojawia się w systemie jako wirtualny port COM (CDC/ACM). Sterowniki instalują się automatycznie na Windows 10/11.USB connection is the simplest and most reliable. The power supply appears as a virtual COM port (CDC/ACM). Drivers install automatically on Windows 10/11.
check_circle Zalecane:Recommended: Do połączenia USB używaj kabla USB-B (typ drukarki) dostarczonego z zasilaczem.Use the USB-B (printer type) cable supplied with the power supply.
RS-232 (legacy)RS-232 (legacy)
Połączenie RS-232 wymaga adaptera USB-RS232. Przetestowane i obsługiwane adaptery:RS-232 connection requires a USB-RS232 adapter. Tested and supported adapters:
- CH340 — popularny i tani, działa na Windows 10/11popular and inexpensive, works on Windows 10/11
- PL2303 — wymagana instalacja sterownika PL2303PL2303 driver installation required
- FT232RL — najwyższa jakość, zalecany do zastosowań profesjonalnychhighest quality, recommended for professional use
Parametry RS-232RS-232 Parameters
| ParametrParameter | WartośćValue |
|---|---|
| Baud rate | 9600 |
| Bity danychData bits | 8 |
| ParzystośćParity | None |
| Bity stopuStop bits | 1 |
| Flow control | None |
| Protokół | tekstowy (KORAD) / Modbus RTU (RIDEN)text (KORAD) / Modbus RTU (RIDEN) |
LAN (tylko KWR102)LAN (KWR102 only)
Zasilacz KORAD KWR102 można obsługiwać przez sieć, bez kabla USB. W Ustawieniach → Połączenie wybierz tryb LAN, a następnie podaj adres IP zasilacza oraz port — domyślnie 18190.The KORAD KWR102 can be operated over the network, without a USB cable. In Settings → Connection select LAN mode, then enter the power supply's IP address and port — 18190 by default.
lan Ustawienia sieciowe zasilacza:Power supply network settings: Po nawiązaniu połączenia program pozwala odczytać i zmienić adres IP, maskę podsieci, bramę, port oraz tryb DHCP wprost z okna ustawień — nie trzeba do tego sięgać po panel urządzenia.Once connected, the program can read and change the IP address, subnet mask, gateway, port and DHCP mode directly from the settings window — there is no need to use the device's own panel.
settings_input_componentKroki konfiguracjiConfiguration Steps
Uruchom K0R@DusLaunch K0R@Dus
Otwórz aplikację. Jeśli to pierwsze uruchomienie, zostaniesz poproszony o aktywację licencji.Open the application. If it is the first launch, you will be prompted to activate your license.
Podłącz zasilaczConnect the power supply
Podłącz zasilacz kablem USB lub RS-232 do komputera. Upewnij się, że zasilacz jest włączony.Connect the power supply with a USB or RS-232 cable to the computer. Make sure the power supply is turned on.
Wybierz port COMSelect COM port
W K0R@Dus otwórz Ustawienia → Połączenie. Z listy wybierz port COM odpowiadający zasilaczowi (np. COM3).In K0R@Dus open Settings → Connection. From the list select the COM port corresponding to the power supply (e.g. COM3).
Zweryfikuj połączenieVerify connection
Kliknij Połącz. Wskaźnik statusu zmieni kolor na zielony, a wyświetlacz pokaże aktualne odczyty z zasilacza.Click Connect. The status indicator turns green and the display shows live readings from the power supply.
warning Bezpieczenstwo:Safety: Zawsze zacznij od ustawienia napięcia wyjściowego na 0 V przed podłączeniem obciążenia do nowego urządzenia. Zapobiega to przypadkowemu uszkodzeniu podłączanego układu.Always start with the output voltage set to 0 V before connecting a load to a new device. This prevents accidental damage to the connected circuit.